How To Fix Whirlpool washer error code e01 f09?

Published & Fact Checked by
Published on:

Ai Disclaimer: We don't use AI for content or research. The contents is researched and written by our team.

» Home » Error Codes » Electronics Products » How To Fix Whirlpool washer error code e01 f09?
Whirlpool Washer Error Code E01 f09

The Whirlpool washer is smart and can get a lot of tasks done than other washers you will find out there.

However, there are some minor hitches that can stall the washer and many users face them.

The good thing is that the developmental team at Whirlpool has taken the time to analyze these issues and code them with different specific error codes.

You can get an idea of what trouble you are having by looking at the error code.

In this article, we will discuss the Whirlpool washer error code e01 f09.

When you see this error code on the washer, it means that the washer is going through issues with drainage.

Why does this exactly happen and what can you do to get rid of the error code, will be discussed in the next section.

How to get rid of the error code e01 f09 on your Whirlpool washer?

The drainage issues on your Whirlpool washer will manifest as the error code e01 f09.

Why are you facing these drainage issues can be a topic of discussion. We will discuss that here with the solutions.

You can easily conduct a diagnosis on the washer so that the washer can give you a detailed analysis of where the problem lies. This will make it easier to fix the problem.

Here are the steps that you can use to enter the diagnosis mode on the Whirlpool Washer.

  • Find the third button and press it.
  • Now press the second button till the time you see the power button flashing
  • Now push the Start button
  • The washer will now enter the diagnostic mode

Fix 1: The hose pipe has an issue

The hose pipe that is connected to the washer should be in a suggested position to make sure that the water exiting the washer during the draining process is not getting stuck there.

If the pipe is bent or broken, you will face the error code informing you that the drainage function is not working.

Check the drain pipe hose. Check for any breaks or bends in the pipe. If the pipe is bent, you can put it in a better position but if it is broken by any chance, you will need to replace the hose pipe.

Fix 2: An issue with the drain pump

The pump that works towards the draining function of the washer needs to be in great shape for the draining function to work properly.

There are some very technical steps that you will need to take in order to check the drain pump. It gets a bit difficult and if you suspect that there is a problem with the pump, you should call in a technician to take a look at the exact issue.

Fix 3: The Central Control Unit is not functioning

The Central Control Unit of the washer is the hub of all the technical function processing on the washer.

If it is not working properly, the commands that are needed for the drainage to be carried out will not be sent. This makes the CCU a very important part that you need to check when you are facing this error code on the washer.

Before you call in a technician, there is certain stuff that you can do on your own.

  • Disconnect the Washer from the power source for safety before you open the washer for any investigation.
  • Take off the top panel of the washer
  • Find the CCU and unplug it.
  • You can also replace the CCU unit with a new one.
  • If none of these options help you or you find replacing the CCU on your own a little bit tricky, get some help.

Fix 4: The pressure switch on the washer is not working

Judging the pressure in the washer and then appropriately sending signals for drainage is the function of the pressure switch.

However, if the pressure switch has been desensitized, you will face a problem with the drainage of the washer.

Check the pressure sensor switch and replace it if it needs replacing.

Fix 5: The drain catch is extremely dirty

The drain catch can quickly get clogged with the gunk that comes out of the drainage of the washer.

You can easily release this pressure on the drain catch. Tr to remove the excess dirty gunk that is clogging the filter. If you do not want to do that, you can also replace the filter with a new one.

Fix 6: Contact the Whirlpool support team

Although we have mentioned every possibility that could be causing the error code to make an appearance on the washer, there are still certain solutions that are fairly technical.

If you are not sure that you can be that technical, it is best to contact the support team.

They can also help you save money if any of your parts can be saved through simple repair instead of buying a new part.

That is a kind of expertise that comes with experience. Also, if the washer is under warranty, you can get it repaired for free or minimal cost.

To conclude

This error code on the Whirlpool washer turns out to be an issue with the improper drainage on the washer.

We have tried to suggest the best fixes but as said before, if you are not sure about any detail, call in a technician because sometimes you can cause more harm than good when you do not know what you are exactly doing.

Keep following for more technical advice.

Like This Post? Checkout More

Photo of author
Falguni Rana is a technology writer who has expertise in software and hardware troubleshooting. She publishes how-to and troubleshooting guides for different apps, websites, games, and consumer hardware products.